Jungheinrich Etv 216 Error Codes Jun 2026

Ensure the battery door is securely closed. Check the sensor connector. Error 1901.1 - Drive Pedal Activated During Startup:

While searching for ETV 216 codes, several related errors from the Jungheinrich family may be helpful:

If a problem persists after your basic troubleshooting, contacting a certified Jungheinrich service technician with these tools is the best course of action.

The diagnostic software, often referred to as , is the tool used to interface with the truck's onboard computer. It can read and clear specific fault codes, perform component calibrations, and program new controllers. jungheinrich etv 216 error codes

For more complex faults, professional diagnostic software is required. Jungheinrich technicians use a proprietary program called . It contains full technical service information, repair instructions, and detailed schematics.

Cause : Bent switch bracket, dirty proximity sensor, or broken wire on the mast. 4. Brake and Safety System Faults (5000-Series)

The system detects an inconsistency in the accelerator pedal or the direction switch signals. Ensure the battery door is securely closed

The system cannot verify the position of the hydraulic control levers (solenoids or joysticks).

Turn off the key switch or log out of the PIN-pad/card reader. Disconnect the main battery plug completely.

| Code | Component | Likely Cause | Quick Check | |------|-----------|--------------|--------------| | | Traction motor | Temperature sensor open circuit | Check wiring to drive motor; sensor resistance should be ~1kΩ at 20°C. | | E 1302 | Lift motor | Overcurrent / short circuit | Inspect lift contactor (K1/K2) for welding; test motor winding insulation. | | E 2101 | Battery management | Battery under voltage (<40V on 48V system) | Charge battery; measure no-load voltage; check cell connectors. | | E 2210 | CAN bus | Communication lost to steering controller | Check CAN-H (white) and CAN-L (yellow) wires at steering wheel column. | | E 3103 | Brake system | Brake release pressure too low (electric-hydraulic brake) | Check brake oil level; bleed the brake circuit. | | F 02 | System | Incorrect truck configuration (e.g., wrong battery capacity programmed) | Requires dealer software (Jungheinrich “Jedi” or “Diagnostic Tool”) to recode. | | F 11 | Controller | Internal memory checksum error | Perform a factory reset (if possible) or replace controller (EVO 80/100). | | 21 (blink code) | Lift/Lower | Lowering valve does not respond | Check coil on lowering valve (12–24V present when lowering requested). | | 28 (blink code) | Steering | Steering encoder signal missing | Inspect encoder on steering motor; clean optical disk if present. | The diagnostic software, often referred to as ,

Often appearing alongside Error 19, this code indicates a communication breakdown between control modules. The description states "Component fails to respond or responds incorrectly to self test".

Your Jungheinrich ETV 216 reach truck is the backbone of your warehouse operations. When an error code flashes on the display, operations slow down, and productivity drops. Understanding these error codes helps you communicate effectively with technicians or safely resolve minor glitches yourself.

| Error Code | Description | Possible Cause | Recommended Action | | :--- | :--- | :--- | :--- | | | Steering wheel sensor bearing fault | Faulty sensor bearing or loose connector; the steering sensor may be slipping on its shaft. | Inspect the sensor and its wiring under the steering wheel. The shaft can sometimes be secured with Loctite as a temporary fix, but replacing the bearing may be necessary. | | 111 | Steering system error | Encoder or sensor failure in the steering system. | Check connectors for damage or corrosion. If the problem persists, a professional recalibration may be required. | | 1d | Steering controller sensor failure | One of the three steering controllers (often called "ELLE") has a failed wheel-sensor (potentiometer/encoder). | Check all three controllers for an error code "d" to locate the bad sensor. In some cases, the sensor may be adjusted. |