Manual !!exclusive!!: Xycd60

Protects against over-discharge (undervoltage). The relay stays closed to power the load until the battery hits the lower limit ( dn ), at which point it disconnects to prevent battery damage. Interesting Technical Highlights

If you can tell me the (lithium or lead-acid) and voltage (12v, 24v, etc.) you are using, I can provide the exact UP and dn values you should set for your XY-CD60 . Share public link

This complete manual serves as a definitive setup and operation guide for configuring the XY-CD60 module for solar setups, battery backup management, and DIY bench testing systems. Technical Specifications Quick Reference Feature / Parameter Specification DC 6V to 60V Control Accuracy Onboard Relay Capacity Operating Current Power Consumption Working Temperature -40°C to 85°C Display Panel High-definition LCD Core Operating Modes Explained

When the detected battery voltage falls below or equals the configured Lower Limit Voltage ( dn ), the onboard relay turns ON (closes the circuit), and external charging current flows into the battery. The display flashes "IN". xycd60 manual

: Typically 10A for the standard XY-CD60, though variants like the XY-CD63 support up to 30A.

Short press UP in normal mode to switch between voltage, percentage, and time.

are you using (Li-ion, LiFePO4, Lead-acid)? What is the voltage of the system (12V, 24V, 48V)? Are you using it for charging or discharging ? Protects against over-discharge (undervoltage)

This guide is based on standard operational parameters for the XY-CD60/XY-CD60L module as seen in common technical datasheets .

: Connect the battery or power source to the VIN+ and VIN- terminals.

The module features two primary working modes: and Discharging Mode (OUT) . Share public link This complete manual serves as

Improper wiring can destroy the module or bypass the protection logic. The terminal layout generally splits into power measurement inputs and switch contacts. Go to product viewer dialog for this item.

Time delay (0-999 seconds) before the relay acts.

Press and hold for 3 seconds to enter programming mode. Use +/- to cycle through parameters:

To maintain and repair the Xycd60:

Protects against over-discharge (undervoltage). The relay stays closed to power the load until the battery hits the lower limit ( dn ), at which point it disconnects to prevent battery damage. Interesting Technical Highlights

If you can tell me the (lithium or lead-acid) and voltage (12v, 24v, etc.) you are using, I can provide the exact UP and dn values you should set for your XY-CD60 . Share public link

This complete manual serves as a definitive setup and operation guide for configuring the XY-CD60 module for solar setups, battery backup management, and DIY bench testing systems. Technical Specifications Quick Reference Feature / Parameter Specification DC 6V to 60V Control Accuracy Onboard Relay Capacity Operating Current Power Consumption Working Temperature -40°C to 85°C Display Panel High-definition LCD Core Operating Modes Explained

When the detected battery voltage falls below or equals the configured Lower Limit Voltage ( dn ), the onboard relay turns ON (closes the circuit), and external charging current flows into the battery. The display flashes "IN".

: Typically 10A for the standard XY-CD60, though variants like the XY-CD63 support up to 30A.

Short press UP in normal mode to switch between voltage, percentage, and time.

are you using (Li-ion, LiFePO4, Lead-acid)? What is the voltage of the system (12V, 24V, 48V)? Are you using it for charging or discharging ?

This guide is based on standard operational parameters for the XY-CD60/XY-CD60L module as seen in common technical datasheets .

: Connect the battery or power source to the VIN+ and VIN- terminals.

The module features two primary working modes: and Discharging Mode (OUT) .

Improper wiring can destroy the module or bypass the protection logic. The terminal layout generally splits into power measurement inputs and switch contacts. Go to product viewer dialog for this item.

Time delay (0-999 seconds) before the relay acts.

Press and hold for 3 seconds to enter programming mode. Use +/- to cycle through parameters:

To maintain and repair the Xycd60: